How hodgdon cfe pistol powder load data can Save You Time, Stress, and Money.

Titegroup is built right here within the USA, which significantly will help availability since it’s not getting delivered from a international state. Additionally it is considerably less position sensitive than other pistol powders, making it perfect for action capturing.

  TiteGroup will not be a good choice as it'll get over tension speedy in 9mm when loaded very hot.   Id Actually Have a look at the BE discussion boards, and appear precisely at 9mm Big loads. Myself, I load 147s with TG for just a cheater load :)

I do not do competitions A lot. If I do, I even now treat them as coaching. Puff loads are neat if you're going to shoot comps and game the technique for time. I don't Individually see the good thing about taking pictures puff loads besides time scoring competitions or teaching a new/younger shooter.

I loaded five distinct cartridges and we analyzed 6 different handloads. I loaded all ammunition on my residence bench employing Lyman’s Brass Smith All American 8. This massive turret press happens to be a favorite of mine for loading each rifle and handgun cartridges.

gdmoody I am going to begin with 5.6 gr and OAL one.a hundred twenty five and provides that a test. I'm definitely liking the LCT press except for the plastic sq. nut on the very best in the indexing rod which broke over the 8th round outside of 10 which i just designed. With any luck , I am able to sneak out towards the vary in the subsequent couple of days.

Iowegan posted something not too long ago about W231 not automatically becoming your best option now for increased velocity .45 ACP loads. I accustomed to load a large amount of Herco in .forty five ACP and .38 Spl, with very good final results. I would like to locate a single powder that does well during the 4 major pistol cartridges I load.

Some ammunition providers checklist 9mm +P+ loads, which are not controlled by SAAMI and therefore are loaded to proprietary tension concentrations and velocities, so are only proposed for select guns.

This gunpowder's declare to fame can it be's power to stop copper fouling; CFE = Copper Fouling Eraser. This advantage may not essentially be of Principal concern for the Open up Division shooters because copper fouling in pistols is not really as problematic as it's in rifles, but any reduction in copper fouling will be welcome.

This can be an older thread, you may not get a reaction, and could be reviving an previous thread. Please consider creating a new thread.

Both of those still left a soot streak on the outside of the case unsure why. Any insight into the soot on the situation?

In the event you’re searching for a versatile powder for revolvers or semi-automobile handguns, CFE Pistol absolutely warrants your attention. That’s the powder that’s front and center Within this story!

Not all fashionable gun suppliers advise Solid bullets in their guns. The situation stems from barrels which might be vulnerable to foremost or are fired with improper load combos that cause leading. If barrels usually are not check here cleaned before utilizing a whole-electricity jacketed bullet load, pressures can spike and conditions can rupture, which may bring about harm to the gun.

Bullet selection to the .45 ACP is wide and includes jacketed, plated, really hard Solid, swaged direct and in many cases increasing sound copper. Substituting bullets which have been of the same pounds which has a supplied powder demand can produce substantially different success and is normally not recommended. Reasons incorporate bullet layout and seating depth that could modify powder capacity, bullet here substance that could modify pressures and velocities, bullet diameter variances, or in regard to swaged lead bullets, they don't seem to be suitable for increased velocities which may result in barrel leading and bad precision.

Dec eight, 2021 #15 I'm working with CFE Pistol since it'll get the job done in the majority of my hand guns and I've 9lbs of it. I have Earlier often chased velocity when reloading(to the extent that precision was still the principal objective), but with component shortages/amplified selling prices I think that Possibly attempting to just settle for reasonable velocities and use a little bit fewer powder would be the approach to go, Except if It is to get a cartridge I hunt with, then I am going to however preserve the very best velocity attainable with fantastic precision.